SciELO - Scientific Electronic Library Online

 
vol.42 número1Assessment of Electrodeposited Zn-ZnO-Agrowaste-Silica Sand Composite as Anticorrosion Material for Mild Steel Substrate in a Marine Environment índice de autoresíndice de assuntosPesquisa de artigos
Home Pagelista alfabética de periódicos  

Serviços Personalizados

Journal

Artigo

Indicadores

Links relacionados

  • Não possue artigos similaresSimilares em SciELO

Compartilhar


Portugaliae Electrochimica Acta

versão impressa ISSN 0872-1904

Port. Electrochim. Acta vol.42 no.1 Coimbra fev. 2024  Epub 29-Fev-2024

https://doi.org/10.4152/pea.2024420101 

Research Article

Surface Corrosion Inhibition of Mild Steel in an Acidic Environment by an Anthelmintic Drug: Experimental, RSM, DFT and MD Simulation Studies

F. O. Edoziuno1  2 

B. U. Odoni1 

A. A. Adediran3  4 

S. Byadi5 

A. Barhoumi6 

C. C. Nwaeju2  7 

L. U. Modebe8 

J. O. Okeniyi9 

1Department of Metallurgical Engineering, Delta State Polytechnic, Ogwashi-Uku, Nigeria

2Department of Metallurgical and Materials Engineering, Nnamdi Azikiwe University, Awka, Nigeria

3Department of Mechanical Engineering, Landmark University, P.O. Box 1001, Omu-Aran, Kwara State, Nigeria

4Mechanical Engineering Science, University of Johannesburg, South Africa

5Department of Chemistry, Hassan II University, Casablanca, Morocco

6Department of Chemistry, Chouaib Doukkali University, El Jadida, Morocco

7Department of Mechanical Engineering, Nigerian Maritime University, Okerenkoko, Delta State, Nigeria

8Department of Chemical Engineering, University of Delta, Agbor, Nigeria

9Department of Mechanical Engineering, Covenant University, Ota, Ogun State, Nigeria


Abstract

Gravimetric, electrochemical, surface investigation, RSM and theoretical computational studies, using DFT and MD, were employed to investigate Ecorr inhibition of MS surfaces in 0.5 M H2SO4, by a worm expelling drug (Wormin® MBZ). The results from computational and RSM optimization and experimental methodologies were all in good accord. After 24 h, IE(%) of 1.5 g/L MBZ on MS corrosion, calculated from WL data, was 96.610%. Maximum IE(%) of 1.0 g MBZ was 96.903% (303 K) and 99.998% (333 K). PDP confirmed MBZ mixed nature of adsorption. The impact of the inhibitor C and IT of MS on IE(%) of MBZ was revealed by statistical evaluation and optimization, using Design Expert software package (Stat-Ease). The optimized IE(%) of 96.6103% was obtained with the inhibitor C of 1.061 g/L, at MS 48.58 h IT. On the MS surface,

MBZ behaved according to Langmuir’s adsorption isotherm. MD showed that MBZ had an Einteraction of -536.33 and -694.53 kcal/mol, at 303 and 333 K, respectively. Negative Einteraction forecasts confirmed MBZ-MS surface interaction capability, which reinforced the experimental investigations IE(%) findings.

Keywords: adsorption; C7H6N2 derivative; DFT; MBZ; MD optimization; RSM; PDP

Introduction

Understanding the physical, mechanical and chemical properties of metallic materials is essential for their efficient usage in structural and building applications. The chemical properties of metals cannot be dissociated from the prevailing service environment and conditions 1-3. Although MS is commonly used for a wide range of industrial applications, because it is readily available at a low cost, and possesses good physical and mechanical properties, it has poor resistance to dissolution in a reactive service environment 4-6. This has led to increasing investigations on how to mitigate MS corrosion 7,8. Corrosion is a type of surface deterioration that occurs when metals are exposed to aggressive environments, due to reactions between them. During many of these industrial processes, MS is exposed to severe corrosive attacks by acid solutions 7,9-11, such as H2SO4, which is widely used in industries for pickling, descaling, acid cleaning, acidizing of oil wells, etc. In order to combat this problem, the use of chemical inhibitors is regarded as one of the most successful techniques, due to their ease of application and cost-effectiveness. However, since most of the compounds examined for CI are either toxic or very expensive, there is a need for further research, in order to identify non-toxic, environmentally benign and inexpensive inhibitors, with good IE(%) at low C 5. A large array of research publications has outlined and described numerous chemical compounds that possess corrosion protection properties. However, only a few of them have been employed as CI in the industries. To some extent, this is because the properties desired for a CI are not limited to the surface protection of metals in service. of Cost, availability, toxicity and eco-friendliness considerations are paramount, due to the rising global ecological campaigns, tougher environmental regulations and sanctions 5,9,11,13-15.

In water presence, which serves as an ion transport channel, metallic electrochemical corrosion occurs when electrons from atoms on the metal surface are transported onto a suitable electron acceptor. The most common electron acceptors (depolarizers) are O, acids and the cations of less active metals. CI are chemical compounds that interact with metallic surfaces, or with their environment, thereby giving them an amount of protection or corrosion resistance 16-18. The effectiveness of organic/inorganic CI is largely determined by factors such as the metal and aggressive solution properties, their mode of interaction, the inhibitor molecular and electronic structure, C, solubility, pH and T 5,19. The most extensively utilized methods to estimate the molecular reactivity of every inhibitors compounds are DFT and MD simulations 20,21. Any fundamental strategy for preventing corrosion must take into account the metal structural properties, the environment, and the reactions that occur between them 21,22. Research found that many organic compounds with N, O, P and S heteroatoms and/or with π-electron systems are employed as metals CI in different service environments 7,10,23. These inhibitors adsorb themselves onto the metallic surfaces, thereby changing the electrical double layer structure 5,11,24-26, and creating a protective surface film on the metal, which serves as a barrier against the aggressive media 9,15,27. Usually, CI are applied by dispersion, or distributed from a solution. Some of them are integrated into the formulation of protective coatings. They work by accelerating anodic or cathodic polarization behaviour, lowering the migration or diffusion of corrosive ions to the metal surface, and increasing its electrical resistance 5.

Many medicinal substances and medication have been identified as possessing chemical characteristics like those of some CI 4,26,28,29, since their chemical structures are similar. This is because they contain electronegative atoms and functional groups that can facilitate their adsorption onto the metallic surface, and form an adherent protective surface film 5,12,16. Medicines used as CI have relatively higher IE(%), as they possess complex molecular structures, with N, O and S multiple hetero-atoms and non-bonding π-electrons 12,28,30. Most heterocyclic medicines, according to reports, are ecologically friendly 16. The present work used MBZ as a chemical inhibitor of MS corrosion in a 0.5 M H2SO4 solution, using experimental and theoretical approaches. MBZ is a synthetic C7H6N2 derivative. It is a white to yellowish powder that is soluble in formic acid and other inorganic acids, but not in water or most organic solvents. MBZ chemical formula is C16H13N3O3, and its molecular weight is 295.30 g/mol 30-33. One of its most common pharmacological use is as an anthelmintic (worm-killing) agent 31. MBZ is being experimentally and theoretically studied as a suitable corrosion inhibitor for MS in H2SO4 and similar acidic service environments, since it is a low cost, non-toxic and biodegradable compound, with O and N hetero atoms in its aromatic ring structure (Fig. 1).

Figure 1: MBZ optimized 3D molecular structure 34,35

Experimental techniques

The following is a step-by-step summary of the experimental methodologies and procedures used in this study.

Materials reparation

Test media

All WL studies were carried out at room T in a 0.5 M H2SO4 solution made from double-distilled deionized water. The experiments were performed with 100 mL of the test media. A local pharmacy provided Wormin® MBZ (made by Cadila Pharmaceutical Ltd., Dholka, India).

Test specimen preparation

The chemical composition of a 16 mm cylindrical MS rod used for this examination was described in the authors’ prior investigations 32,33. The rod was meticulously cut and sliced into several 15 x 10 mm long test coupons. For the specimens suspension, a 5 mm hole was drilled in their centre.

Before each experiment, MS samples were polished with numerous grades of emery paper (from 800 to 1200), and, afterwards, they were cleaned with distilled water and cleansed with acetone.

FTIR spectroscopy characterization of the inhibitor

Agilent Technologies’ FTIR Cary 630 was used to assess MBZ functional properties. During the analysis, the inhibitor sample was scanned using transmittance method, and FTIR spectra were acquired over a wavenumber range from 650 to 4000 cm-1, with a resolution of 8 cm-1. MBZ chemical bond information and functional groups were detected using FTIR characterization.

WL measurements

MS test coupons were weighed and suspended in in 100 mL beakers containing the prepared test media, for 24, 48, 72, 96 and 120 h IT, with and without MBZ. They were removed when the required IT expired. The corrosion products were removed from MS samples by washing them in distilled water, rinsing in acetone and drying in ambient air. The coupons were then re-weighed to obtain their final weights. WL measurement findings are shown in Table 1. CR (mL/year) was calculated using Eq. 1.

()

where D is density (g/cm2) and A is area (cm2). IE(%) for MBZ was calculated using the relationship given in Eq. 2a.

()

CRc and CRi were determined without and with MBZ various C, respectively. IE(%) of MBZ was calculated for all its C during various IT of MS in H2SO4. θ by MBZ was determined using Eq. 2b.

()

Curves showing the relationship between IE(%) of MBZ, C and θ, and IT of MS, were also plotted.

Electrochemical measurements

IE(%) of MBZ was evaluated using a VersaSTAT 4 Electrochemical System auto lab potentiostat/galvanostat, controlled from a PC suitably equipped through a USB interface, and with Versa Studio electrochemistry software suite. All the experiments were conducted in a Pyrex glass cell with three electrodes. The WE was a test piece enclosed in polyester resin, with a total area of 1 cm2 exposed to a corrosive liquid, and the CE was a Pt rod. The RE was an Ag/AgCl rod. These electrodes were connected to the electrolytic cell by a Luggin capillary. All the electrochemical test procedures and parameters were per the authors’ previous investigations 32,35, and their values are shown in Tables 2 and 3. IE(%) was calculated according to Eq. 3.

()

where icorri and icorrc were determined for the MS coupon in the H2SO4 solution without and with MBZ, respectively, at a specified C.

SEM characterization of the MS surface

Following WL measurements, the corroded MS coupons surface morphology was scanned and examined by a SEM Phenom Pro X Model (Phenom world, Eindhoven, Netherlands) equipped with appropriate EDXS, for elemental and corrosion product characterization. The scanning techniques and SEM instrument parameters were reported in the authors’ previous studies 32,35,36.

DFT studies

All quantum chemical investigations were carried out utilizing DFT/B3LYP methods with the 6-311 G (d, p) basis set, which is very reliable for geometrical optimizations, using the Gaussian 09 software. Because corrosion occurs in the aqueous phase, it is computationally appropriate to incorporate the solvent effect. Hence, all quantum computations were done in the aqueous phase, using SCRF theory and PCM. HOMO, and LUMO have been measured as quantum chemical characteristics linked to 37,38 ELUMO, EHOMO and Δ. In an aqueous solution, µ and N110 were computed using Gaussian 09 W 39.

∆N from MBZ molecules onto the MS surface, during inhibitor-metal interaction, was computed using Eq. 4.

()

∅ value was 4.82 eV, and Fe was 0 40. When ∆N is greater than zero, the metal electron transfer inhibition occurs, i.e., ∆N > 0.

Fukui indices, which indicate the reactive centres within the molecules, may be used to analyse local reactivity 41.

MDS

Accelrys Inc.'s Materials Studio 6.0 42 was used to run MD simulations in a simulation box with periodic boundary conditions. A 5 slab was utilized to cut the Fe crystal, which was imported and cleaved along the (110) plane. The smart minimizer system was used to reduce the Fe (110) surface energy, which alleviated it. The Fe (110) surface was extended to a (10) supercell, in order to provide a large surface for the inhibitor action. A vacuum slab was built with a thickness of zero. A supercell with the dimensions of a = 28.66 Å, b = 40.53 Å and c = 33.24 Å, comprising 250 H2O, 20H3O+, 10H2SO2 and 1 MBZ molecule, was created based on molecules to sulfate proportion in 0.5 M H2SO443. The test was run in a simulation box (28.66, 40.53, 33.24 Å3), at 303/333 K, NVT ensemble (constant no. of atoms, volume and T) and COMPASS force field 44, with a time step of 1 fs and a total simulation time of 500 ps.

Einteraction and Ebinding determined using Eqs. (5) and (6) 45,46 were employed to understand MBZ/Fe (110) interfaces in the simulation framework.

()

()

where Etotal is the entire system total energy, Esurface + solution is the total energy of the Fe (110) surface and HCl without inhibitor, and Einhibitor is MBZ total energy.

Optimization of IE(%) and other corrosion properties using RSM

Researchers have attempted to describe and optimize CI factors, and anticipate their responses using experimental design software packages and approaches such as RSM 47-50. IE(%) and other corrosion parameters were changed using RSM, based on the CCD tool of Design-Expert software version 11. A quadratic design model was employed in the investigation. WL, CR, IE(%) and θ were employed as response variables (1 to 4), while C and IT were employed as independent factors (1 and 2). To acquire the optimized responses of the dependent variables, a total of 30 tests runs was carried out.

Results and discussion

FTIR spectroscopy analysis

Fig. 2 illustrates FTIR spectra for MBZ.

Figure 2: FTIR spectra for MBZ. 

CI and molecular adsorption of MBZ onto MS surfaces in H2SO4 were due to the functional groups and bond types within its structure. Inside MBZ molecular structure, due to NH group, there was a band from 3276 to 2113.4 cm-1, which is associated with intense stretching of the imidazole ring 7,51. C=N group was in the ranges from 1743 to 1595 cm-1. C=C group was in the ranges from 1431 to 1241 cm-1. The bands from 1241 to 1051 cm-1 and from 984 to 711.9 cm-1 depict in-plane and out of plane CH bending deformation of the imidazole ring, respectively. CH3 strong symmetric and asymmetric stretching bonds were also assigned from 3026.6 to 2918.5 cm-1 (52. C-C ring stretching vibrations were observed at the frequency bands from 1643.8 to 1431.3 cm-1 in FTIR spectra.

Gravimetric measurements

Table 1 shows WL and CR of MS, and IE(%) for MBZ, whereas Figs. 3 to 10 show a graphical representation and comparison of the corrosion parameters. At several C (0, 0.5, 1.0, 1.5, 2.0 and 2.5 g), IE(%) of MBZ against MS corrosion, in 0.5 M H2SO4, was investigated.

Table 1: CI results from WL of MS in 0.5 M H2SO4, at various IT, without and with MBZ, in various C. 

IT (h) CI properties Inhibitor C (g/L)
Blank 0.5 1.0 1.5 2.0 2.5
24 WL (g) 1.77 0.14 0.11 0.07 0.06 0.08
CR (mm/yr) 1.31 0.10 0.08 0.05 0.04 0.06
IE(%) - 93.79 96.05 96.61 95.48 92.09
( - 0.94 0.96 0.96 0.95 0.92
48 WL (g) 3.18 0.17 0.22 0.22 0.13 0.15
CR (mm/yr) 1.18 0.06 0.08 0.08 0.05 0.06
IE(%) - 94.65 93.08 93.08 95.91 95.28
( - 0.95 0.93 0.93 0.96 0.95
72 WL (g) 1.76 0.36 0.22 0.1 0.32 0.13
CR (mm/yr) 0.43 0.09 0.05 0.02 0.08 0.03
IE(%) - 87.5 94.32 81.82 92.61 79.55
( - 0.88 0.94 0.82 0.93 0.80
96 WL (g) 2.11 0.5 0.45 0.28 0.38 0.31
CR (mm/yr) 0.39 0.09 0.08 0.05 0.07 0.06
IE(%) - 78.67 86.73 81.99 85.31 76.30
( - 0.79 0.87 0.82 0.85 0.76
120 WL (g) 3.74 0.41 0.35 0.32 0.48 0.35
CR (mm/yr) 0.55 0.06 0.05 0.05 0.07 0.05
IE(%) - 90.64 91.44 87.17 90.64 89.04
( - 0.91 0.91 0.87 0.91 0.89

WL (g), CR (mm/yr), IE(%) (76.303-96.610%) and θ (0.76303-0.96610) ranges showed that MBZ effectively protected MS in H2SO4. This was due to MBZ molecules and atoms adsorption onto the MS test coupons surface, which formed a surface barrier coating against H2SO4. MS low CR and WL values obtained by gravimetric measurements (Fig. 1) was due to IE(%) and θ relatively high values for MBZ, because of its ringed structure with N and O heteroatoms, and nonbonding π-electrons 30,53. These hetero-atoms and free-electron sites enabled MBZ adsorption onto the MS surface, providing it with enough corrosion resistance.

CR values of MS in 0.5 M H2SO4 were substantially reduced with its higher IT and C of MBZ, due to the inhibitor molecules action on the alloy surface (Figs. 3 and 4). CR was the lowest (0.024667 mm/yr), after 72 h IT of MS in the H2SO4 solution with 1.5 g/L MBZ. MBZ highest IE(%)was 96.610% for MS in 1.5 g/L H2SO4, with 24 h IT. MBZ was particularly successful as CI on MS in 0.5 M diluted H2SO4, as proven by the fact that CR and WL of the latter were much lower in the solution with the former than in the one without it.

Figure 3: CR of MS in HCl for different IT at various C of MBZ. 

Figure 4: Variation in CR (mm/yr) for MS with C of MBZ. 

WL (Fig. 5), for MS in 0.5 M H2SO4 without and with MBZ, in varying C, was remarkably reduced when the latter was added to the corrosive solution. On a close inspection, WL of MS decreased to a maximum, with higher C of MBZ, and longer IT, before maintaining a near-constant value, and then it slight increased. The test without MBZ recorded the highest WL and CR values for MS during its IT.

Figure 5: Dependence from WL of MS on IT. 

Fig. 6 revealed a marked reduction in WL, as C of MBZ was increased from 0 to 2.5 g/L, for all the considered IT. MBZ successfully decreased the CR of MS in H2SO4 to a minimal level. The plots of CR, IE(%) and θ against IT and C, as shown in Figs. 3, 4, 7-10, revealed a similar trend.

Figure 6: Dependence from WL of MS on C of MBZ. 

Fig. 7 shows that IE(%) decreased with higher IT, but remained above 70% for all IT, and increased with growing C of MBZ (Fig. 8).

Figure 7: Effect of IT for MS in 0.5 M H2SO4 on its corrosion IE(%) by different C of MBZ. 

Figure 8: Dependence from CI of MS by MBZ on its C, for various IT in 0.5 M H2SO4

Figs. 9 and 10 show that MBZ protective thin film provided enough coverage of the MS surface in H2SO4, throughout the IT, significantly reducing active corrosion sites.

Figure 9: Dependence from θ by MBZ on the IT of MS in 0.5 M H2SO4

Figure 10: θ variation with different C of MBZ. 

Electrochemical measurements

PDP measurements

Fe anodic breakdown to Fe2+ is thought to be the cause of MS corrosion in aggressive acidic environments 54-56. Using Tafel extrapolation/polarization measurements, the effect of MBZ various doses on MS anodic dissolution, and on the related cathodic reduction of H ions during the corrosion process, was determined. MBZ addition to the H2SO4 solution moderately changed anodic and cathodic half-reactions, as seen by Tafel plots in Figs. 11 and 12.

Figure 11: PDP curves for MS in 0.5 M H2SO4 without and with MBZ, in various C, at 303 K. 

Figure 12: PDP curves for MS in 0.5 M H2SO4 without and with MBZ, in various C, at 333 K. 

Tafel curves extrapolation yielded PDP values shown in Tables 2 and 3. MBZ addition resulted in Ecorr huge displacement, as it can be seen in the tables. For all C of MBZ, anodic and cathodic Tafel constants were available. This suggests that MBZ is a mixed-type inhibitor. According to the overall polarization data, the trial without MBZ exhibited the highest CR. PDP test revealed that MBZ had a significant impact on the electrochemical process that led to the corrosion reaction. In addition, differences in the cathodic and anodic Tafel constants between the H2SO4 solution without and with MBZ indicate that redox reactions connected with the corrodent were impeded by the thin film formed by the inhibitor 18. The development of an adherent protective coating, and MBZ adsorption onto the MS surface, can be linked to the inhibitor corrosion IE(%) 18,35,57,58. Icorr values for the tests with MBZ and without it reinforce this conclusion (Tables 2 and 3). Since Ecorr displacement obtained in the test without MBZ (Tables 2 and 3) was less than 85 mV, at 303 and 333 K, it was deduced that it functioned as a mixed-type inhibitor, based on PDP data 30,59.

Table 2: PDP values for MS in 0.5 M H2SO4 without and with different MBZ C at 303 K. 

MBZ C (g/L) Icorr (mA) Ecorr (mV) CR (mm/yr) IE(%) (a (mV) (c (mV)
0.0 -3.352 -470.939 24.779 - 198.367 123.246
0.5 -179.323 -442.306 1.3254 94.651 130.587 89.324
1.0 -103.823 -437.697 0.76734 96.903 121.614 67.34
1.5 -155.868 -452.045 1.152 95.351 122.923 80.257
2.0 -136.153 -437.823 1.0063 95.939 131.168 76.031
2.5 -138.462 -464.284 1.0234 95.870 124.738 91.449

Table 3: PDP values for MS in 0.5M H2SO4 without and with MBZ in different C, at elevated T (333 K). 

MBZ C (g/L) Icorr (mA) Ecorr (mV) CR (mm/yr) IE (%) (a (mV) (c (mV)
0.0 -34.01 -440.497 251.37 - 400.406 351.646
0.5 -12.06 -396.102 89.136 64.540 317.637 173.616
1.0 -563.79nA -422.048 0.0041669 99.998 83.216 129.55
1.5 -1.765 -422.933 13.049 94.809 173.434 78.959
2.0 -1.66 -430.981 12.274 95.117 185.951 89.983
2.5 -1.876 -419.401 13.867 94.483 214.317 67.60

Furthermore, H2SO4 solutions with MBZ had lower icorr values than those of the blank ones. MBZ addition reduced cathodic and anodic half-reactions, thus supporting also the inference that it is a mixed type inhibitor 30,36.

At 303 and 333 K, corrosion IE(%) obtained using PDP parameters was slightly higher than that calculated using WL data. At 303 K, 1.0 g MBZ inhibited MS corrosion in H2SO4, with a maximum IE(%) of 99.998%. At 303 K, 1.0 g MBZ gave a maximum IE(%) of 96.903%. The similarity in the corrosion IE(%) values obtained at ambient T, by both gravimetric and PDP techniques, suggest agreement of both methods.

T effect

At 303 and 333 K, T effect on CR and IE(%) was investigated. As a rule of thumb, the rate of a chemical reaction doubles at every 283.15 K increase in T; so, corrosion kinetics, as an electrochemical process, should increase as T rises 32. With MBZ, a modest decrease in IE(%) and an increase in CR were detected at higher T, implying the creation of a physical/electrostatic adsorption coating 60,61. On the other hand, chemisorption occurs when there is an increase in IE(%), a drop in CR with higher T, lower acid C, and decreased Ea rate 60,61. MBZ lower IE(%) and MS higher CR observed in 0.5 M H2SO4 with low inhibitor C, at 333 K, revealed that the critical C of anions required for metals and alloys corrosion protection rose with higher T and aggressive solutions C 53,60,62.

Analysis of adsorption isotherms

The concept of molecular adsorption can be used to further explain CI mechanisms, as it is generally affected by the inhibitor chemical structures, the charge distribution in the molecule, the metal nature and surface charge, and the type of corrosion media 18,61. Evaluation of experimental data obtained with multiple adsorption isotherms is used to determine the most likely method of adsorption. Frumkin’s, Temkin’s, Freundlich’s and Langmuir’s isotherms are the most commonly used adsorption models for researching the inhibition mechanism of the corrosion process. Based on the given mathematical relations, Kads and G°ads values were calculated (Eqs. 7 and 8). The adsorption isotherms characterize the inhibitor molecules interactions with the active corrosion sites on the metal surface 5, and give more information on the CI mechanism. In this study, Temkin’s and Langmuir’s adsorption isotherms were investigated to determine MBZ adsorption mechanism onto the MS surface. With a linear graph, near unity slopes (1.0423 and 0.969) and R2 values of 0.9999 and 0.9839, at 303 and 333 K, Langmuir’s adsorption isotherm provided the best and most suitable description of MBZ behaviour, confirming its constituents adsorption onto the corroding MS surface. The interactions of the adsorbate species with the MS surface, as well as variations in Qads with increasing θ, can be attributed to the modest departure of the slopes and R2 of the Langmuir’s plot from unity 63. The linear form of the Langmuir’s adsorption isotherm given in Eq. 7 was used to plot the adsorption isotherm provided in Fig. 13.

(7)

Figure 13: Langmuir’s adsorption isotherms for MS in 0.5 M H2SO4 with various C of MBZ, at 303 and 333 K. 

The change in ΔG°ads was obtained using Eq. 8:

(8)

where R is the universal gas constant (8.314 kJ−1/mol−1) and 55.5 is the molar C (mol/L−1) of water in the solution. Kads and ΔG°ads values were obtained at various T and MBZ C (Table 5). High Kads and negative ΔG°ads values were obtained for MBZ molecules, which implies their effective and spontaneous adsorption onto the MS surface in 0.5 M H2SO4. ΔG°ads magnitude is a decisive factor in the adsorption process. Physisorption is generally associated with ΔG°ads values around -20 kJ·mol-1 and below, while chemisorption is attributed to ΔG°ads values around -40 kJ·mol-1 and above 5,7,9,32,35. ΔG°ads estimated values for MBZ varied from -15.4720 to -18.7870 and from -14.6965 to -18.0345 kJ/mol-, at 303 and 333 K, respectively, as shown in Table 4.

Table 4: ΔG°ads, θ and Kads calculated for MBZ in 0.5 M H2SO4

T (K) MBZ C (g/L) ΔG°ads (kJ/mol-1) Kads (mol-1) θ
303 0.5 -18.7870 35.3902 0.94651
1.0 -18.4818 31.2893 0.96903
1.5 -16.4303 13.6703 0.95350
2.0 -16.0665 11.8037 0.95939
2.5 -15.4720 9.2852 0.95870
333 0.5 -14.6965 3.6402 0.64540
1.0 -15.5749 4.9990 0.99998
1.5 -18.0345 12.1538 0.94809
2.0 -17.4214 9.7396 0.95117
2.5 -16.4471 6.8503 0.94483

This indicates that MBZ adsorption process was physisorption. As T and C of MBZ were increased from 303 to 333 K and from 0.5 to 2.5 g/L, respectively, ΔG°ads and Kads values decreased; a similar pattern was described in the literature 27,32.

SEM analysis

Figs. 14a and b show micro-analytical pictures of MS specimens before and after corrosion, with and without MBZ.

Figure 14: SEM surface morphology of MS specimens after gravimetric experiments in H2SO4: (a) without MBZ and (b) with MBZ. 

The blank H2SO4 solution corroded the MS surface (Fig. 14a), which has a significantly deteriorated morphology, with obvious and deep macro and micro pits. Due to MBZ corrosion IE(%)on MS, Fig. 14b depicts a transition to a relatively smooth surface shape.

DFT studies

DFT-based structural analysis can be used to assess C7H6N2 carbamate MBZ derivative reactivity. Δ, EHOMO, ELUMO and N110 are considered good overall indices for assessing MBZ IE(%) of MS surfaces corrosion 64. In acidic media, protons are assumed to be present, making the protonation of organic molecules more likely. The most critical protonation site is displayed in Fig. 15, and MBZ had no active protonation site in acidic Ph, for fixing H+ to a pH of 3.42.

Figure 15: Possible MBZ molecules forms by varying pH from 0 to 14. 

Thus, it was assumed that the molecule was stable at the acidic pH used in this experiment, as assessed by Marvin View software. At an acidic pH (pHexp of 0.5 M H2SO4 is pH = -log(0.5) = 0.301), MBZ had no protonation state, which means that the only neutral form remained in the solution. This is beneficial, because several experiments have shown that the protonation form of the molecule is not absorbed.

MBZ molecule optimal configurations and molecular electrostatic E distribution are shown in Fig. 16. The most stable and energy-efficient systems are interconnected systems. The average density (red colour) of MEP distribution is centred on O atoms of carbonyl groups; O8 atom has several electrons in this circumstance, facilitating the sharing phenomenon with the vacant iron orbitals 65.

Figure 16: MBZ optimized frameworks and MEP distribution. 

The distribution of electron density in molecular frontier orbitals (HOMO and LUMO) is described as global reactivity, as seen in Fig. 17, where HOMO electron density can be found on any chemical surface, except on the phenyl group linked to the carbonyl function. This demonstrates that MBZ contains a large number of active electron donor sites throughout the skeleton. LUMO electron density is represented over a wide section of the compound surface, except for the phenyl group, implying considerable adsorption of this substance onto the metal surface. EHOMO high value (-5.4754 eV) for MBZ indicates that it can effectively exchange electrons with empty spaces on the metal surface. This means that MBZ-metal is highly reactive. MBZ positive value of ΔN, but less than 3.6 (Table 5), means that it can release and share its electrons 66-68. O (O8 and O20) and C7H6N2 ring electron cloud are the active centres in MBZ, and they are responsible for this electron sharing behaviour. The µ descriptor interprets the polarizability of the chemical compounds under investigation; high polarizability (reactivity), i.e. strong adsorption of the inhibitory molecule onto the metallic surface, is shown by a high value of this descriptor 69.

Figure 17: FMO distributions for MBZ. 

Local reactivity is a popular strategy for determining the local active areas of a chemical inhibitor 70.

Tables 5 and 6 show the chemical structure descriptors and calculated Fukui indices of simplified functions (f+ and f-) for MBZ, respectively.

Table 5: Descriptors of MBZ molecule chemical structure. 

Complex ELUMO EHOMO µ Δ ΔN
MBZ-Fe -2.1135 -5.4754 4.9782 3,3619 2.5744

Table 6: Fukui indices for MBZ f+ k and f- k measured at DFT/GGA/DNP. 

Atom f + k f - k Atom f + k f - k
1 C 0.16820 -0.12004 12 C -0.15573 0.22856
2 C -0.13104 0.11047 13 C 0.16297 -0.09522
3 C 0.13203 -0.06242 14 C 0.21594 -0.07532
4 C 0.08012 -0.06134 15 C 0.34829 -0.19004
5 C 0.08959 -0.01851 16 C -0.18038 0.28582
6 C 0.09187 -0.06577 17 C 0.46978 -0.47136
7 C 0.07746 0.08726 18 N 0.27686 -0.22970
8 O 0.03460 0.11203 19 C -0.02668 0.06965
9 C -0.10926 0.08992 20 O 0.06293 0.00204
10 C 0.32256 -0.18432 21 O -0.00853 0.01471
11 C -0.13117 0.12038 22 C 0.31706 -0.31829

Fig. 18 shows the condensed atom Fukui functions, while Tables 5 and 6 show the chemical structure descriptors and calculated Fukui indices of simplified functions (f+ and f-) for MBZ. Atoms with higher f- and f+ values are electrophilic and nucleophilic active centres, respectively 71. The findings show that O(8) atom underwent electrophilic assaults, indicating that it was prone to supply electrons, forming more stable coordination bonds with the metal surface. During nucleophilic assaults, atoms like C(10), C(12) and C(16) will accept electrons from the metal surface.

Figure 18: MBZ atom-condensed Fukui functions for f+ k and f- k estimated at DFT/GGA/DNP, using Material studio software. 

Electronic conduct of Fe-MBZ complex

Fe-MBZ complex was investigated using DFT method, to see how the metal surface affected the inhibitor electron density distribution and quantum chemical descriptors. The chemical quantum computing was done with the Gaussian 09 software, and DFT was done on the B3LYP/LanL2DZ level. Fig. 19 shows Fefrontier-molecular MBZ orbitals, optimized structure and electronic density distribution.

Figure 19: Fe-MBZ complex FMO distributions and MBZ Fe-O(11) distance. 

There was no visible change in spatial conformation for MBZ optimized structure coupled to the Fe atom, when compared to its structure alone. As a result, Fe and O atoms are at the core of HOMO mass (O8). HOMO high density on the Fe atom indicates that it has received electrons from the inhibitor, resulting in a decrease in MBZ electronic density. LUMO, on the other hand, is almost on the complex structure. Therefore, the result for MBZ alone is the same. Hence, MBZ electron donor property to Fe atom was improved. Table 7 groups key quantum chemical descriptors values. Fe iron atom had a favourable impact on overall chemical reactivity, according to the results in this table. A drop in Δ and an increase in ΔN and µ values demonstrated this. These findings show that MBZ and Fe surface communicated effectively.

Table 7: Chemical structural descriptors for Fe-MBZ complex. 

Complex EHOMO ELUMO µ Δ ΔN
MBZ-Fe -3.5793 -1.3926 11.4998 2.1866 1.06739

MD modeling

When the adsorption mechanism at the MBZ-metal interface was studied, theoretical modelling methods concentrated on MD simulation 72. When the inhibitor adsorbed onto the adsorbate, the fluctuation energies and T curves (303 and 333 K) were in equilibrium, as shown in Figs. 20 and 21, which illustrate top and lateral views of MBZ adsorption configurations on MS surface in H2SO4, at 303 and 333 K.

Figure 20: MD structures of MBZ adsorption onto the Fe(1 1 0) surface, at 303 K. 

Figure 21: MD structures of MBZ adsorption onto the Fe(1 1 0) surface, at 333 K. 

MBZ structure is visible on the initial Fe surface, indicating that the inhibitor molecule was firmly adsorbed. This could be due to the presence of covalent bonds at the MBZ-Fe (1 1 0) contact, which positively modified the adsorption behaviour.

This technique maximized θ qualities, by adsorbing the C7H6N2 derivative. Indeed, this species is a powerful CI, confirming IE(%) findings of the experimental studies. Energy concepts, explicitly, Ebinding and Einteraction, were used to express the simulation findings. The magnitude of MBZ adsorption and contact with the MS surface was determined by the values of these terms. Negative touch energy projections confirmed MBZ-metal contact capabilities 73. At 303 and 333 K, corresponding Einteraction values for MBZ were -536.33 and -694.53 kcal/mol, respectively.

Results of optimization by RSM

WL, CR, IE(%)and θ were all affected by inhibitor C and IT, according to the results of optimization research. Figs. 22, 23 and 24 illustrate MBZ IE(%) on MS in 0.5 M H2SO4. Fig. 22 shows a linear graph of anticipated versus real IE(%), suggesting that the design model was adequate for predicting MBZ inhibition 50.

Figure 22: Diagnostic plot of predicted versus actual IE(%). 

IE(%) level of reliance for MBZ C and IT was demonstrated by the 3-D surface plot (Fig. 23).

Figure 23: 3-D surface plot for IE(%) with the predicted value. 

3-D surfaces structure suggests that, throughout the CI process, there were considerable interactions between the evaluated factors and the response variables. Fig. 24 shows a perturbation plot that can be used to compare the effects of various parameters on IE(%), at different points in the design space. Only one element changed over the response range, while the other remained constant. For all factors, the reference point was set by default to the midpoint (coded 0). This can be altered to any desirable point (perhaps the optimal run conditions). A component with a steep slope or curve implies that it is sensitive to the response. The response variable is insensitive to changes in that particular component, if the line is reasonably flat. The perturbation plot demonstrates the element that has the most impact on the response. IE(%) of MBZ was more responsive to its C (B) than to IT (A), in this case.

Figure 24: Perturbation curve showing the most influential factor. 

Eq. 9 provides a predictive model Eq. of MBZ IE(%), as a function of the components evaluated in terms of factors coding. The quartic model Eq. represented the link between IE(%) and independent parameters, such as MBZ C (B) and IT (A). For given levels of each factor, the model Eq. written in terms of factor coding can be used to predict the response of the dependent variable. By default, the high values of the components are recorded as +1, while the low levels are coded as -1. By comparing the factors coefficients, the relative impacts of the elements can be determined using the coded Eq. 50.

()

Table 8 contains a summary of the design parameters. F-value of 83.80 suggests a significant model, according to ANOVA results in Table 9. Due to noise, such high

F-value has a 0.01% probability of occurring. Model terms that have a value of prob > F less than 0.0500 are considered significant. A, B, A3, B3 and B4 are the model significant terms in this example. Insignificant model terms are indicated by values greater than 0.1000. Since the difference is smaller than 0.2, pred. Rsquared of 0.9506 is in reasonable agreement with adj. R-squared of 0.9756. These values are quite close to unity, indicating that the model was well-fit 74. The signal-to-noise ratio is measured using adeq. precision. A signal-to-noise ratio of more than 4 is always preferable. The research yielded a signal-to-noise ratio of 27.497, indicating that the signal was strong, and that this model may be utilized to navigate the design space effectively.

Tables 8: Design summary for factor and response variables. 

Table 9: Response parameter (IE(%)) ANOVA results. 

Numerical optimization result

Table 10 presents the optimal solutions found to suitably satisfy the target optimization goals set for the factors and the responses after numerical optimization.

The optimization report reveals that a minimum inhibitor C of 1.061 g/L was required, for 48 h IT, in order to obtain an optimal IE(%) of 96.61%, with near-unity desirability (0.879).

Table 10: Numerical optimization report. 

Time MBZ C WL CR IE(%) ( Desirability
48.581 1.061 0.060 0.084 96.610 0.922 0.879

Conclusions

WL measurements, PDP techniques, design optimization, DFT and MD modelling were used to study MS corrosion and its inhibition in 0.5 M H2SO4. Based on the analysis and interpretation of the findings, the study concluded that:

According to the findings of the Tafel polarization investigation, MBZ acted as a mixed type CI, and its adsorption onto the MS surface followed Langmuir’s isotherm.

MBZ, at C of 1.061 g/L, exhibited an optimal IE(%) of 96.610% in 0.5 M H2SO4, after 48.58 h.

MBZ is highly efficient for MS surface CI in H2SO4.

DFT and MD studies show that increasing T improved MBZ IE(%), and that its adsorption onto the MS surface was proportional to T, corroborating the findings on T effect and molecular adsorption sections.

A quartic predictive model Eq. accurately illustrated the reliance of MBZ IE(%) on the investigated independent elements of the inhibition process in the operational environment.

Acknowledgement

The authors gratefully recognize the Tertiary Education Trust Fund (TETFund), Nigeria, for its financial support of this study under the Institution Based Research (IBR) Interventions.

Authors’ contributions

F. O. Edoziuno: conceived and designed the analysis; conceptualized ideas; performed the experiment and analysis; analyzed data; wrote the paper- developed some sections of the manuscript. B. U. Odoni: performed gravimetric experiments; wrote the paper - developed some sections of the manuscript. A. A. Adediran: conceived and designed the analysis: conceptualized ideas; offered key intellectual support, assessed and appraised the manuscript. S. Byadi: performed the analysis-MD simulation; analyzed data; wrote the paper - developed some sections of the manuscript. A. Barhoumi: performed the analysis - MD simulation; and analyzed data; wrote the paper - developed some sections of the manuscript. C. C. Nwaeju: assisted in the predictive modelling, optimization, edition of the manuscript and plagiarism test. L. U. Modebe: offered key intellectual support, assessed, reviewed and appraised the manuscript. J. O. Okeniyi: performed the analysis; offered key intellectual support, assessed, reviewed and appraised the manuscript.

Abbreviations

AgCl: silver chloride

AIC: Akaike information criterion

ANOVA: analysis of variance

BIC: Bayesian information criterion

C7H6N2: benzimidazole

C: concentration

CCD: central composite design

CE: counter electrode

CI: corrosion inhibition/inhibitor

CR: corrosion rate

CV: coefficient of variation

Df: degree of freedom

DFT: density functional theory

DNP: double numerical plus polarization

Ea: activation energy

Ebinding: binding energy

Einteraction: interaction energies

Ecorr: corrosion potential

EDXS: energy dispersive X-ray spectroscopy

EHOMO: energy of the highest occupied molecular orbital

ELUMO: energy of the lowest unoccupied molecular orbital

G°ads: standard free energy of adsorption

H2SO4: sulphuric acid

icorr: corrosion current density

IE(%): inhibition efficiency

IT: immersion time

Kads: adsorption equilibrium constant

MBZ: mebendazole (methyl-5-benzoyl-2-benzimidazole: C7H6N2 carbamate derivative)

MD: molecular dynamics

MEP: molecular electrostatic potential

MS: mild steel

N110: height of transmitted electrons

PCM: polarized continuum model

PDP: potentiodynamic polarization

Qads: heat of adsorption

R2: determination coefficient

redox: reduction and oxidation reactions

RE: reference electrode

RSM: response surface methodology

SCRF: self-consistent reaction field

SD: standard deviation

SEM: scanning electron microscopy

T: temperature

WE: working electrode

WL: weight loss

Kinetic parameters

(a: Tafel anodic slope

(c: Tafel cathodic slope

Δ: energy gap

ΔG°ads: Gibb’s free energy of adsorption

∆N: fraction of transferred electrons

µ: dipolar moment

ηFe: metal hardness

ηinh: inhibitor hardness

(: degree of surface coverage

∅: job function

χinh: inhibitor electronegativity

References

1. Loto CA, Popoola API, Fayomi OS, et al. Corrosion polarization behaviour of type 316 stainless steel in strong acids and acid chlorides. Int J Electrochem Sci. 2012;7:3787-3797. [ Links ]

2. Bothi Raja P, Sethuraman MG. Inhibitive effect of black pepper extract on the sulphuric acid corrosion of MS. Mater Lett. 2008;(62) 17-18:2977-2979. DOI: https://doi.org/10.1016/j.matlet.2008.01.087 [ Links ]

3. Nishimura R, Tsuru T, Ohtsuka T, et al. Understanding of Corrosion Phenomena: Process, Mechanism, and Method. Int J Corros. 2012:286174. DOI: https://doi.org/10.1155/2012/286174 [ Links ]

4. Gupta NK, Gopal CSA, Srivastava V, et al. Application of expired drugs in corrosion inhibition of MS. Int J Pharm Chem Analyt. 2017;(4)1:8-12. DOI: https://doi.org/ 10.18231/2394-2797.2017.0003 [ Links ]

5. Peme T, Olasunkanmi LO, Bahadur I, et al. Adsorption and corrosion inhibition studies of some selected dyes as corrosion inhibitors for MS in acidic medium: Gravimetric, electrochemical, quantum chemical studies and synergistic effect with iodide ions. Molecules. 2015;20:16004-16029. DOI: https://doi.org/10.3390/molecules200916004 [ Links ]

6. Ofuyekpone O, Akaluzia RO, Edibo S. Investigating the influence of immersion time and inhibitor C on the inhibiting potential of Imperata cylindrica as Corrosion Inhibitor of MS. Int J Res Eng Innov. 2017;1:147152. DOI: http://www.ijrei.com [ Links ]

7. Mashuga ME, Olasunkanmi LO, Adekunle AS, et al. Adsorption, thermodynamic and quantum chemical studies of 1-hexyl-3methylimidazolium based ionic liquids as corrosion inhibitors for MS in HCl. Materials (Basel). 2015;8:3607-3632. DOI: https://doi.org/10.3390/ma8063607 [ Links ]

8. Finsgar M, Jackson J. Application of corrosion inhibitors for steels in acidic media for the oil and gas industry: A review. Corros Sci. 2014;86:17-41. DOI: https://doi.org/10.1016/j.corsci.2014.04.044 [ Links ]

9. Nwabanne JT, Okafor VN. Adsorption and thermodynamics study of the inhibition of corrosion of MS in H2SO4 medium using Vernonia amygdalina. J Miner Mater Charact Eng. 2012;11:885-890. [ Links ]

10. Sivakumar V, Velumani K, Rameshkumar S. Colocid Dye - A Potential Corrosion Inhibitor for the Corrosion of MS in Acid Media. Mater.Res. 2018:21:4. e20170167. DOI: https://doi.org/10.1590/1980-5373-MR-2017-0167 [ Links ]

11. Oguzie EE, Li Y, Wang FH. Corrosion inhibition and adsorption behaviour of methionine on MS in sulfuric acid and synergistic effect of iodide ion. J Collo Interf Sci. 2007;310:90-98. DOI: https://doi.org/10.1016/j.jcis.2007.01.038 [ Links ]

12. Karthikeyan S. Drugs/antibiotics as potential corrosion inhibitors for metals- a review. Int J Chem Tech Res. 2016;(9)6:51-259. [ Links ]

13. Al-Otaibi MS, Al-Mayouf AM, Khan M, et al. Corrosion inhibitory action of some plant extracts on the corrosion of MS in acidic media. Arab J Chem. 2014;7:340-346. DOI: https://doi.org/10.1016/j.arabjc.2012.01.015 [ Links ]

14. Stango SAX, Vijayalakshmi U. Studies on corrosion inhibitory effect and adsorption behaviour of waste materials on MS in acidic medium. J Asian Ceram Soc. 2018;6: 20-29. DOI: https://doi.org/10.1080/21870764.2018.1439608 [ Links ]

15. Loto RT. Surface coverage and corrosion inhibition effect of Rosmarinus officinalis and zinc oxide on the electrochemical performance of low carbon steel in dilute acid solutions. Results Phys. 2018;8:172-179. DOI: https://doi.org/10.1016/j.rinp.2017.12.003 [ Links ]

16. Eddy NO, Odoemelam SA, Ekwumemgbo P. Inhibition of the corrosion of MS in H2SO4 by penicillin G. Sci Res Essay. 2009;(4)1:033-038. [ Links ]

17. Loto CA, Loto RT, Osugbunu O, et al. Corrosion inhibition effect of Allium Cepa extracts on MS in HCL. Der Pharma Chem. 2016;8:20:20-30. DOI: http://derpharmachemica.com/archive.html [ Links ]

18. Loto CA, Loto RT, Joseph OO. Effect of benzamide on the corrosion inhibition of MS in sulphuric acid. South Afri J Chem. 2017;70:38-43. DOI: https://doi.org/10.17159/0379-4350/2017/v70a6 [ Links ]

19. Karthik G, Sundaravadivelu M. Inhibition of MS Corrosion in Sulphuric Acid Using Esomeprazole and the Effect of Iodide Ion Addition. ISRN Electrochem. 2013:1-10. DOI: https://doi.org/10.1155/2013/403542 [ Links ]

20. Dagdag O, El Harfi A, Cherkaoui O, et al. Rheological, electrochemical, surface, DFT and molecular dynamics simulation studies on the anticorrosive properties of new epoxy monomer compound for steel in 1 M HCl solution. RSC Adv. 2019;9:4454. DOI: https://doi.org/10.1039/C8RA09446B [ Links ]

21. Oguzie EE, Li Y,. Wang SG, et al. Understanding corrosion inhibition mechanisms - Experimental and theoretical approach. RSC Adv. 2011;1: 866-873. DOI: https://doi.org/10.1039/c1ra00148e [ Links ]

22. Dagdag O, Safi Z, Erramli H, et al. Adsorption and anticorrosive behaviour of aromatic epoxy monomers on carbon steel corrosion in acidic solution: computational studies and sustained experimental studies. RSC Adv. 2019;9:14782-14796. DOI: https://doi.org/10.1039/c9ra01672d [ Links ]

23. Paul S, Koley I. Corrosion Inhibition of Carbon Steel in Acidic Environment by Papaya Seed as Green Inhibitor. J. Bio- Tribo-Corros. 2016;2:2-11. DOI: https://doi.org/10.1007/s40735-016-0035-2 [ Links ]

24. Nahlé A, Abu-Abdoun II, Abdel-Rahman I. Inhibition of MS corrosion by 3benzoylmethyl benzimidazolium hexafluoroantimonate in acidic solution. Int J Corros. 2012:246013. DOI: https://doi.org/10.1155/2012/246013 [ Links ]

25. Moreira RR, Soares TF, Ribeiro J. Electrochemical Investigation of Corrosion on AISI 316 Stainless Steel and AISI 1010 Carbon Steel: Study of the Behaviour of Imidazole and Benzimidazole as Corrosion Inhibitors. Adv Chem Eng Sci. 2014;04:503-514. DOI: https://doi.org/10.4236/aces.2014.44052 [ Links ]

26. Ngobiri NC, Okorosaye-Orubite K. Adsorption and corrosion inhibition characteristics of two medicinal molecules. Chem Int. 2017;(3)2:185-194. [ Links ]

27. Hassan KH, Khadom AA, Kurshed NH. Citrus aurantium leaves extracts as a sustainable corrosion inhibitor of MS in sulfuric acid. South Afr J Chem Eng. 2016;22:1-5. DOI: https://doi.org/10.1016/j.sajce.2016.07.002 [ Links ]

28. Verma C, Chauhan DS, Quraishi MA. Drugs as environmentally benign corrosion inhibitors for ferrous and nonferrous materials in acid environment: An overview. J Mater Environ Sci. 2017;(8)11:4040-4051. [ Links ]

29. Gece G. Drugs: A review of promising novel corrosion inhibitors. Corros. Sci. 2011;53:3873-3898. DOI: https://doi.org/10.1016/j.corsci.2011.08.006 [ Links ]

39. Ahamad I, Quraishi MA. Mebendazole: New and efficient corrosion inhibitor for MS in acid medium. Corros Sci. 2010;52:651-656. DOI: https://doi.org/10.1016/j.corsci.2009.10.012 [ Links ]

31. Al-Kurdi Z, Al-Jallad T, Badwan A, et al. High-performance liquid chromatography method for determination of methyl-5-benzoyl-2benzimidazole carbamate (mebendazole) and its main degradation product in pharmaceutical dosage forms. Talanta. 1999;50:1089-1097. DOI: https://doi.org/10.1016/S0039-9140(99)00212-X [ Links ]

32. Edoziuno FO, Adediran AA, Odoni BU, et al. Performance of Methyl-5Benzoyl-2-Benzimidazole Carbamate (Mebendazole) as Corrosion Inhibitor for MS in Dilute Sulphuric Acid. Sci World J. 2020:1-11. DOI: https://doi.org/10.1155/2020/2756734 [ Links ]

33. Odoni BU, Edoziuno FO, Chukwurah NC. Corrosion inhibition potential of methyl-5-benzoyl-2-benzimidazole carbamate (mebendazole) for MS in 1.0 M sulphuric acid. Int J Res Eng Innov. 2017;1:190-194. DOI: http://www.ijrei.com [ Links ]

34. Edoziuno FO, Odoni BU, Adediran AA, et al. Analyses of the Gravimetric and Electrochemical Effects of C16H13N3O3 on MS Corrosion in 0.5 M H2SO4. J Phys Conf Ser. 2019;1378:032064. DOI: https://doi.org/10.1088/17426596/1378/3/032064 [ Links ]

35. Edoziuno FO, Adediran AA, Odoni BU, et al. Influence of wormin mebendazole on the corrosion of MS in 1.0M sulphuric acid. Results Eng. 2021;9:100192. DOI: https://doi.org/10.1016/j.rineng.2020.100192 [ Links ]

36. Edoziuno FO, Adediran AA, Odoni BU Odoni, et al. Comparative analysis of corrosion inhibition effects of mebendazole (MBZ) on MS in three different sulphuric acid concentrations. Int J Corros Scale Inhib. 2020;9:1049-1058. DOI: https://doi.org/10.17675/2305-6894-2020-9-3-17 [ Links ]

37. Xia G, Jiang X, Zhou L, et al. Synergic effect of methyl acrylate and Ncetylpyridinium bromide in N-cetyl-3-(2-methoxycarbonylvinyl)pyridinium bromide molecule for X70 steel protection. Corros Sci. 2015;94:224-236. DOI: https://doi.org/10.1016/j.corsci.2015.02.005 [ Links ]

38. Sadik K, Byadi S, Aboulmouhajir A. Quantum and dynamic investigations of complex iron- alkaloid-extract Cytisine derivatives of Retama monosperma (L.) Boiss. Seeds as eco-friendly inhibitors for MS corrosion in 1 M HCl. J Mol Struct. 2021(1244)15:130921. DOI: https://doi.org/10.1016/j.molstruc.2021.130921 [ Links ]

39. Neese F, Wennmohs F, Becker U, et al. ORCA 3.0.1 Manual (Input Description), 2014. [ Links ]

40. Cao Z, Tang Y, Cang H, et al. Novel benzimidazole derivatives as corrosion inhibitors of MS in the acidic media. Part II: Theoretical studies. Corros Sci. 2014;83: 292-298. DOI: https://doi.org/10.1016/j.corsci.2014.02.025 [ Links ]

41. Pearson RG. Absolute Electronegativity and Hardness: Application to Inorganic Chemistry. Inorg Chem. 1988;27:734-740. DOI: https://doi.org/10.1021/ic00277a030 [ Links ]

42. Akkermans RLC, Spenley NA, Robertson SH. Monte carlo methods in materials studio. Mol Simul. 2013;39:1153-1164. DOI: https://doi.org/10.1080/08927022.2013.843775 [ Links ]

43. Salarvand Z, Amirnasr M, Talebian M, et al. Enhanced corrosion resistance of MS in 1 M HCl solution by trace amount of 2-phenyl-benzothiazole derivatives: Experimental, quantum chemical calculations and molecular dynamics (MD) simulation studies. Corros Sci. 2017;114:133-143. DOI: https://doi.org/10.1016/j.corsci.2016.11.002 [ Links ]

44. Sun H. Compass: An ab initio force-field optimized for condensed-phase applications - Overview with details on alkane and benzene compounds. J Phys Chem B. 1998;102:7338-7364. DOI: https://doi.org/10.1021/jp980939v [ Links ]

45. Saha SK, Dutta A, Ghosh P, et al. Novel Schiff-base molecules as efficient corrosion inhibitors for MS surface in 1 M HCl medium: Experimental and theoretical approach. Phys Chem Phys. 2016;(18)27:17898-17911. DOI: https://doi.org/10.1039/c6cp01993e [ Links ]

46. Saha SK, Dutta A, Ghosh P, et al. Adsorption and corrosion inhibition effect of schiff base molecules on the MS surface in 1 M HCL medium: A combined experimental and theoretical approach. Phys Chem. 2015;17:5679-5690. DOI: https://doi.org/10.1039/c4cp05614k [ Links ]

47. Anadebe VC, Onukwuli OD, Omotioma M, et al. Optimization and Electrochemical Study on the Control of MS Corrosion in Hydrochloric Acid Solution with Bitter Kola Leaf Extract as Inhibitor. South Afr J Chem. 2018;71:51-61. DOI: https://doi.org/10.17159/0379-4350/2018/v71a7 [ Links ]

48. Omotioma M, Onukwuli OD. Modeling the Corrosion Inhibition of MS in HCl Medium with the Inhibitor of Pawpaw Leaves Extract. Port Electrochim Acta. 2016;34: 287-294. DOI: https://doi.org/10.4152/pea.201604287 [ Links ]

49. Gutiérrez E, Rodríguez JA, Cruz-borbolla J, et al. Development of a predictive model for corrosion inhibition of carbon steel by imidazole and benzimidazole derivatives. Corros Sci. 2016;108:23-35. DOI: https://doi.org/10.1016/j.corsci.2016.02.036 [ Links ]

50. Edoziuno FO, Adediran AA, Odoni BU, et al. Optimization and development of predictive models for the corrosion inhibition of MS in sulphuric acid by methyl-5-benzoyl-2-benzimidazole carbamate (mebendazole). Cogent Eng. 2020;7:1714100. DOI: https://doi.org/10.1080/23311916.2020.1714100 [ Links ]

51. Raducka A, Czylkowska A, Gobis K, et al. Characterization of Metal-Bound Benzimidazole Derivatives, Effects on Tumor Cells of Lung Cancer. Materials (Basel). 2021;14:2958. DOI: https://doi.org/10.3390/ma14112958 [ Links ]

52. Oturak H, Kinaytürk NK, Cirak C . Experimental and Theoretical Spectral (FT-IR, Raman, NMR, UV-Vis and NLO) Analysis of a potential antitumor drug: 1-Methyl-6-Nitro-1H-Benzimidazole. Spectrosc Spectr Analyt. 2018;(38)6:1963. DOI: https://doi.org/10.3964/j.issn.1000-0593(2018)06-1963-07 [ Links ]

53. Popova A, Sokolova E, Raicheva S, et al. AC and DC study of the temperature effect on MS corrosion in acid media in the presence of benzimidazole derivatives. Corros Sci. 2003;45:33-58. DOI: https://doi.org/10.1016/S0010938X(02)00072-0 [ Links ]

54. Sherif ESM. Corrosion inhibition in 2.0 M sulfuric acid solutions of high strength maraging steel by aminophenyl tetrazole as a corrosion inhibitor. Appl Surf Sci. 2014;292:190-196. DOI: https://doi.org/10.1016/j.apsusc.2013.11.110 [ Links ]

55. Sherif ESM, Abbas AT, Halfa H, et al. Corrosion of high strength steel in concentrated sulfuric acid pickling solutions and its inhibition by 3-amino-5mercapto-1,2,3-triazole. Int J Electrochem Sci. 2015;10:1777-1791. DOI: https://doi.org/10.13140/RG.2.2.10951.91046 [ Links ]

56. Sherif ESM, Abbas AT, Gopi D, et al. Corrosion and Corrosion Inhibition of High Strength Low Alloy Steel in 2.0 M Sulfuric Acid Solutions by 3Amino-1,2,3-triazole as a Corrosion Inhibitor. J Chem. 2014. DOI: https://doi.org/10.1155/2014/538794 [ Links ]

57. Loto CA, Joseph OO, Loto RT. Inhibition effect of Vernonia amygdalina extract on the corrosion of MS reinforcement in concrete in 0.2 M H2SO4 Environment. Eur J Environ Civ Eng. 2013;17:10:1026-1038. DOI: https://doi.org/10.1080/19648189.2013.841596 [ Links ]

58. Loto CA, Joseph OO, Loto RT. Inhibition effect of zinc oxide on the electrochemical corrosion of MS reinforced concrete in 0.2 M H2SO4. J. Mater Environ Sci. 2016;7:915-925. [ Links ]

59. Riggs jr. OL. Corrosion Inhibition, Second ed, C.C. Nathan, Houston, TX, 1973. [ Links ]

60. Nnanna LA, Owate IO, Oguzie EE. Inhibition of MS Corrosion in HCl Solution by Pentaclethra macrophylla Bentham Extract. Int J Mater Eng. 2014;4:171-179. DOI: https://doi.org/10.5923/j.ijme.20140405.02 [ Links ]

61. Olawale O, Adediran AA, Talabi SI, et al. Inhibitory action of Vernonia amygdalina extract ( VAE ) on the corrosion of carbon steel in acidic medium. J Electrochem Sci Eng. 2017;7:145-152. DOI: https://doi.org/10.5599/jese.353 62. [ Links ]

62. Popova A. Temperature effect on MS corrosion in acid media in presence of azoles. Corros Sci. 2007;49:2144-2158. DOI: https://doi.org/10.1016/j.corsci.2006.10.020 [ Links ]

63. Chidiebere MA, Nnanna L, Blessing AC, et al. Inhibition of Acid Corrosion of MS Using Delonix Regia Leaves Extract. 2016;69:74-86. DOI: https://doi.org/10.18052/www.scipress.com/ILCPA.69.74 [ Links ]

64. Louadi YE, Abrigach F, Bouyanzer A, et al. Theoretical and experimental studies on the corrosion inhibition corrosion current density of two tetrakis pyrazole derivatives for MS in 1.0 M HCl. Port Electrochim Acta. 2017;35:159-178. DOI: https://doi.org/10.4152/pea.201703159 [ Links ]

65. Olasunkanmi LO, Obot IB, Kabanda MM, et al. Some quinoxalin-6-yl derivatives as corrosion inhibitors for MS in hydrochloric acid: Experimental and theoretical studies. J Phys Chem C. 2015;119:16004-16019. DOI: https://doi.org/10.1021/acs.jpcc.5b03285 [ Links ]

66. Pais M, Shwetha N, Rao P. Experimental and Theoretical Evaluation of Efficacy of Inhibitory Action of Benzyl Isothiocyanate Prot. Met. Phys Chem Surfaces. 2021;57:597-607. DOI: https://doi.org/10.1134/S2070205121030187 [ Links ]

67. Benhiba F, Hsissou R, Benzekri Z, et al. DFT/electronic scale. MD simulation and evaluation of 6-methyl-2-(p-tolyl)-1,4-dihydroquinoxaline as a potential corrosion inhibition. J Mol Liq. 2021;335:116539. DOI: https://doi.org/10.1016/j.molliq.2021.116539 [ Links ]

68. Rodríguez JA, Cruz-Borbolla J, Arizpe-Carreón PA, et al. Mathematical models generated for the prediction of corrosion inhibition using different theoretical chemistry simulations. Materials (Basel). 2020;13:5656. DOI: https://doi.org/10.3390/ma13245656 [ Links ]

69. Laabaissi T, Benhiba F, Rouifi Z, et al. Benzodiazepine Derivatives as Corrosion Inhibitors of Carbon Steel in HCl Media: Electrochemical and Theoretical Studies Prot. Met Phys Chem Surfaces. 2019;55:986-1000. DOI: https://doi.org/10.1134/S2070205119050149 [ Links ]

70. Oguike RS, Kolo AM, Shibdawa AM, et al. Density Functional Theory of MS Corrosion in Acidic Media Using Dyes as Inhibitor: Adsorption onto Fe(110) from Gas Phase. ISRN Phys Chem. 2013. DOI: https://doi.org/10.1155/2013/175910 [ Links ]

71. Contreras RR, Fuentealba P, Galvan M, et al. A direct evaluation of regional Fukui functions in molecules. Chem Phys Lett. 1999;(304)5-6:405-413. DOI: https://doi.org/10.1016/S0009-2614(99)00325-5 [ Links ]

72. Rahmani H, Alaoui KI, El Azzouzi M, et al. Corrosion assessment of MS in acid environment using novel triazole derivative as an anti-corrosion agent: A combined experimental and quantum chemical study. Chem Data Collect. 2019;24: 100302. DOI: https://doi.org/10.1016/j.cdc.2019.100302. [ Links ]

73. Singh A, Ansari KR, Haque J, et al. Effect of electron-donating functional groups on corrosion inhibition of MS in hydrochloric acid: Experimental and quantum chemical study. J Taiwan Inst Chem Eng. 2018;82: 233-251. [ Links ]

74. Kothari CR, Garg G. Research Methodology: Methods and Techniques, 3rd ed., New Age International (P) Ltd., Publishers, New Delhi, 2014. [ Links ]

Received: March 21, 2022; Accepted: May 31, 2022

Corresponding author: francisedoziuno@gmail.com

Creative Commons License This is an open-access article distributed under the terms of the Creative Commons Attribution License